Just how to Replace a Bath Tub (Step By Step).
Just how to Replace a Bath Tub (Step By Step).
Blog Article
We have stumbled on the article involving How to Install a Bathtub Yourself down the page on the web and felt it made good sense to relate it with you on this page.
Installing a bathtub isn't exactly rocket science, however it does need strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily available, the job can move rapidly; if you have to open a wall to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the brand-new one. Make certain you have qualified yourself for the work and also fit trying it. Instead of employing a professional to take over a halfway-completed task, it is much better to consider employing one prior to you start. Possibilities are you may need a specialist plumber to make tube links.
This short article will aid you mount a new bathtub in your washroom if you have already bought a brand-new bathtub and don't require to alter the arrangement of your previous water supply pipelines.
Your devices and product checklist should consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your setup, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of removing the existing faucets can be quite troublesome due to the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this process. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making certain that the washers remain in place between the faucet and the sink. Protect the faucet in place with the maker given backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous type ought to be attached to the tap ends initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Bathtub
Utilizing both wood boards under its feet, position the bath tub in the required position. The wooden boards are useful in evenly spreading the weight of the tub over the area of the boards rather than focusing all the weight onto four little factors.
The following objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the outermost adaptable faucet connector to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and check all joints and new pipework for leaks as well as tighten them if needed. Fill up the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bath tub needs to wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it right into its final setting.
Getting ready for the Setup
Firstly, the sustaining structure provided with the bath ought to be fitted (if required) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is very important to make sure that if the faucet features a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets system to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you use all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final placement.
Tiling Around the Bathtub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to fracture a rigid seal, creating the water to penetrate the wall surface between the bath and also the tiling, resulting in difficulties with dampness as well as possible leaks to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and fittings. They are marketed in tubes and cartridges, as well as can sealing spaces approximately a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to constantly fill the tub with water prior to sealing, to enable the motion experienced when the bathtub is in use. The sealer can fracture fairly very early if you do not think about this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are additionally conveniently available on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or waterproof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was guided to that editorial about Tools You Need to Install a New Bathtub through a good friend on another site. Do you know someone else who is truly interested in the subject? Do not hesitate to share it. Bless you for your time. Visit again soon.
Book A Free Estimate Report this page